Engine
Volvo Penta
Total Power
23hp
Engine Hours
2122
Class
Cutter
Length
8.53m
Year
1985
Model
28
Capacity
-
SEA Marine
Boat Details
Description
This 1985 Lyle Hess Bristol Channel Cutter was purchased in 2007 for intended travels to Alaska and around the world. She was rerigged in 2008, has Autopilot, Cape Horn windvane, Solar, Garmin, diesel heater, Uniden VHF, SSB, Sea Anchor and spares, Gimballed 3-burner propane stove, Composting head, original Tanbark sails, 2023 inflatable dinghy with Mercury outboard, Copper sheeting on the bottom, and much, much more.
Junessa is powered by a 2003, 23hp 3-cylinder Volvo Penta with approximately 2122 hours, last oil change 4/11/2025.
This boat is LOADED, but her decks could use work.
Owner's overseas position forces sale.
Please call to arrange viewing. Junessa is currently located at SEA Marine, Port Townsend.
Contact Information
Other Details
Accommodations and Layout
Sleeping arrangements amidships, head forward. Sleeping arrangements under way are on port and starboard settees with lee cloths and port and starboard pilot berths aft. The amidships settees can be combined for a queen-sized bed for “in-port” accommodations. Forward of main stateroom is forecastle with work bench to starboard, hanging locker/bin to port and composting head center. Generous chain locker and line locker (open) forward.
Headroom 6'1".
Galley
Galley is directly below companionway
Icebox and sink to starboard
Gimbaled propane stove/oven to port
Safety rails on both sides
Propane tank mounted on outside deck
Electronics and Navigation
Autohelm autopilot
Garmin GPS
4-inch Plastimo compass
Autohelm ST50 depth sounder, wind speed indicator and speed/distance log
Icom 718 all-band 2-100/watt SSB
Uniden VHF radio
Stereo /CD player
Clock and Barometer
All manuals and associated books
Life ring
Life sling
406 EPIRB
Electrical System
12V DC and 110V AC systems
2 batteries
Battery parallel switch
20-amp automatic battery charger
Shore power cord
2 solar panels (Solaris 5M/60M); 40-watt each at 2.2AH
Deck
Teak decks need work
Dinghy with 3.5hp Mercury
35# CQR anchor; 225-feet 5/16-inch chain
45# Danforth-type anchor; 200-feet ½-inch nylon with chain leader
25# Danforth anchor
65# bronze 3-piece Herreshoff anchor
Bow pulpit, rails, lifelines and side stanchions
Hull
Built by Channel Cutter Yachts, Vanvouver, BC
Full keel with outboard rudder
Hull is white with green trim
Copper foil (3M) applied to bottom
Pilothouse can be unbolted and removed
Sails and Rigging
Manual boom vang
Elliott Pattison tanbark sails
Mainsail, jib, spinnaker, #1 genoa, staysail, new storm trysail, blooper and drifter
Profurl roller furling on both headsails
S/S wire standing rigging
Self-tailing bronze Barient winches
Keel-stepped aluminum mast
Spinnaker pole
Whisker pole
Engine and Mechanical
2 automatic and 2 manual bilge pumps
Manual fire extinguishing
Range 200-nm
Fuel filters
Fresh water cooling
Stove and engine fuel shut-off valves
Diesel heater
2 extra propellers
Tiller steering
2.4:1 transmission ratio
2 35-gallon water tanks
Electric water heater
Disclaimer
The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.
Propulsion
Engine Make:Volvo Penta
Engine Year:1985
Total Power:23hp
Engine Hours:2122
Engine Type:Inboard
Drive Type:Direct Drive
Fuel Type:Diesel
Propeller Type:3 Blade
Propeller Material:Bronze
Specifications
Dimensions
Length Overall:11.28m
Beam:3.05m
Cabin Headroom:1.85m
Miscellaneous
Hull Material:Fibreglass
Tanks
Fresh Water Tank:264.98 l
Fuel Tank:102.21 l
Holding Tank:37.85 l
Accommodations
Crew Heads:1