1994 Mason 4413m

     The world class designer Al Mason certainly designed one of the most beautiful ocean-going vessels you will ever see. And the builder, Ta Shing is well recognized for quality. The attention to detail is evident everywhere you look.

     The Mason 44 is a beautiful, capable ocean-going sailboat with graceful sweeping lines and beautiful overhangs with a full keel with a substantial cut away in the fore foot. The large rudder provides excellent turning ability and the long keel gives tremendous directional control in all conditions. The rudder sits up four inches from the keel bottom providing a grounding safety assurance and is secured in a place with a heavy bronze shoe. Engine and generator placement is below the salon sole to lower the CGs and provides quieter running. It also provides excellent engine access and allows for a straight shaft, direct drive. With the propeller angle is perpendicular to the water plane you get greater efficiency and performance.

     “The Mason 44 was designed and constructed to meet and exceed specifications set forth by the American Bureau of Shipping and Lloyd’s for fiberglass yacht construction. All laminations took place in dehumidified air-conditioned lay-up rooms. Materials such as fiberglass, resin, foam, etc., are also stored within climatically controlled areas as mandated by Lloyd’s regulations. Every Mason was built to the same rigorous standards.

     The Mason 44 hull is completely hand laminated with eight full-length longitudinal foam-filled stringers. Heavy laminated transverse transvers stringers, double bonded ¾” structural bulkheads, and joiner bulkheads used for interior furniture assured a rigid structure capable of withstanding a great deal of abuse…

     A vertical-end grain balsa core separated two hand laid laminates of one-piece molded fiberglass deck. The deck was secured to the hull using a combination of 3-M 5200 epoxy compound, heavy fiberglass bonding of six laminates, thru bolts on 8” centers and self-tapping stainless-steel screws on on 8” centers. Many designers of production fiberglass “offshore cruising boats” endorsed identical hull to deck joint construction but without the fiberglass lamination. The Mason 44 had without a question the toughest hull to deck joint in the industry.

     It should be noted that there are no less than six ¾” structural bulkheads in a Mason 44, all of which are attached to fiber rope (mare’s tale) and three alternating laminates of 1 ½ oz. matt and woven roving on both sides of mahogany bulkhead. The foam between the bulkhead and the hull insures no hard spots on bulkhead transfer visible from the yachts exterior. Every joinery bulkhead (of which there are dozens) is also attached to the deck and hull using two alternating layers of fiberglass matt and woven roving. Also note that one of eight full-length foam and fiberglass longitudinal stringer. No other yacht offers this level of security and peace of mind.” ~ Pacific Asian Enterprises

     “Only the highest quality electropolished stainless steel was used for the deck hardware onboard the Mason 44.  All stanchions bases, chocks, hinges, and bow rollers were fabricated from forged stock. Virtually no cast fittings were used insuring void-free rugged gear.” ~ Pacific Asian Enterprises

     Deck is cored fiberglass sandwich and molded nonskid with oversized hardware featuring:

• Factory gel coat molded nonskid decks
• Bulwark all around with scuppers and teak cap rail
• Exterior teak cap rail and handrails
• Solid stainless stem head fitting with anchor platform on small sprit
• Double bow roller and electric windlass
• Stainless steel bow pulpit
• Mast safety pulpit
• Stainless steel stanchions with boarding gates port and starboard
• Stainless steel 1" tubular life line
• (6) Standard mooring cleats are all 8" bow, stern, and mid ships
• (6) Lewmar opening deck hatches with hatch covers
• (8) Stainless steel opening ports
• Stainless dorades with fiberglass boxes
• Deck prisms for natural lighting over chart table and galley
• Deck scuppers drain at the water line
• Side mounting swim/boarding ladder folds down
• Stern pulpit
• Edson outboard motor mount on 1” stainless steel stern rail
• Vented propane locker holding two 20 lb. tanks

     Spacious comfortable cockpit destroyer wheel and leather cover

• Edson destroyer wheel
• Suite of electronics (see Electronics)
• Anchor controls at the pedestal
• Molded seating with cockpit cushions
• Edson teak cockpit table – removable
• Drink holders
• Teak flag staff
• Stern rail
• Spray curtains for cockpit privacy
• Fresh water hot and cold shower in cockpit
• Deep cockpit locker to starboard
• Dodger of beige Sunbrella 
• Beautiful sacrificial cover for the cockpit and equipment in cockpit
• Companionway hatch boards
• Large cockpit drains
• Manual bilge pump in cockpit
• Cockpit shower- hot and cold

    “The design, fabrication, and installation of the chainplates on a Mason 44 is an example of the many details on which a Mason buyer gets their money’s worth. On the standard cutter-rigged boat, the double spreader rig utilizes a individual chainplate for both the upper and intermediate stays. The upper and intermediate chainplates, as with all the chainplates, are forged stainless steel measuring ½” x 2” and running below the deck level over 36”. Both chainplates are attached to a primary structural bulkhead which is reinforced with two ¾” mahogany doublers. The total thickness of this chainplate attachment is just under three inches, including all the fiberglass lamination. The two chainplates are anchored to either side of the bulkhead with eight 7/16’ stainless steel bolts. The fore and aft lower chainplates which are ¼” x 1 ¾” are similarly anchored to a ¾” mahogany webs laminate with three alternating layers of 1 ½ oz. matt and woven roving plus the mare’s tails as discussed in the structural bulkhead attachment.”  ~ Pacific Asian Enterprises

     Entropia is a delight to sail with Harken roller furling (2020) for both the jib and a tidy Dutchman to manage the mainsail and the beautiful Anderson electric primary winches, jib winches overhauled in 2021 with factory 3 year warranty.

• Forespar cream painted aluminum mast Awlgripped ~ repainted 2020
• Keel stepped
• Double spreader cutter rig with storm track
• Wire 1/19 stainless-steel wire rigging with Navtec terminals ~ 2020
• Running backstays for storm conditions ~ 2020
• Navtec boom vang and back stay, overhauled
• Lewmar blocks
• Harken roller furler for headsail
• Harken traveler
• Jib tracks with double cars
• Harken turning blocks
• Harken Batt car system for mainsail
• Dutchman system
• Separate storm trysail track on the mast
• Topping lift
• Mast mounted carbon fiber pole rigged for spinnaker
• Mid boom sheeting to Harken traveler forward of dodger
• Slab reefing system with reefing winch on the mast
• Preventer system

     Sail Inventory

• Fully battened Hallet 8.8 oz. mainsail with two reef points ~ 2019
• Quantum Hydranet Cross Cut furling genoa
• Quantum Furling Staysail 
• Doyle A-Spinnaker 1.5 oz. ~ 1998
• Storm Trysail and storm trysail track ~ never used

     Winches

• (2) Anderson 54 electric self-tailing primary winches on the cockpit combing
• (2) Lewmar 30 staysail sheet winches on cockpit combing
• (1) Anderson 40 self-tailing mainsheet winch on coach roof
• Halyard winches on the mast, two #30s, and two #16
• Reefing winch on the mast for easy reefing on either tack, #16
• Mast safety pulpit for secure reefing
• Stainless steel winch handles

     Helm Station

• Garmin GPSMap 7212 touch screen chart plotter/multi-function display
• AIS
• Simrad autopilot controls with linear hydraulic ram
• (3) Garmin GAMI/10 multi-function displays (above companionway)
• Garmin remote marine VHF
• Ritchie Powerdamp ships compass

     Navigation Station

• Garmin GPSMap 7212 touch screen chart plotter/multi-function display
• AIS
  
• Garmin GMI/10 multifunction display
• Garmin VHF 200 marine VHF
• Furuno GPS/WAAS Navigator
• Simrad WR20 Autopilot controller
• Iridium Satellite phone with external antenna
• Clarion stereo receiver

     On Mast

• Garmin closed array radar dome

• Engine: Yanmar 50HP Model 4JH2E with 3,252 hours 
• Dual lever engine controls and engine instrument panel with tach, temp, oil pressure, and warning lights and alarms
• Balmar 110 amp alternator with smart regulator ~ 2018
• Fuel capacity is 165 gallons in two tanks
• Cruising speed at 6.5 to 8.5 knots
• Engine instruments – tachometer, temp, oil pressure
• Racor 500 fuel filter
• Groco strainer
• PSS shaft seal
• Bronze rudder stock packing gland
• Direct drive stainless steel shaft 1.25 in
• Max Prop in protected aperture 18” by 22 pitch
• Shaft and prop zinc
• Edson wheel steering
• Hydraulic autopilot
• Automatic fire suppression system in engine room
• Bow thruster
• Webasto diesel furnace

     “The main electrical panels were manufactured by Pacific Asian Enterprises. The custom designed and built panel uses magnetic circuit breakers exclusively.” ~ Pacific Asian Enterprises

     Complete 110 volt and 12-volt systems with shore power connection and charging system and Northern Lights Genset with about 1100 hours. Bonded and grounded with lightening protection system.

    12 Volt DC system:

     (3) 8D AGM 200 amp/hour batteries for house, in 2016 professionally installed and secured, plus (2) 8D AGM engine start battery. Balmar 100 amp alternator for engine charging and solar panels on top of cockpit bimini for additional charging needs. 

• Mason 44 custom 12-volt DC distribution panel
• Go Power 30 amp PWM digital solar controller at helm
• Xantrex monitoring system
• Balmar Smartgauge advanced battery monitoring system
• Electronics
• LED Navigation lights deck level
• LED anchor light
• LED steaming light
• LED stern light
• LED spreader/deck lights
• LED cabin lights (red and white)
• (5) Reading lamps
• Hella cabin fans
• 12-Volt USB outlets
• Electric bilge pump Rule 1500
• Shower sump pump
• Pressure water pump
• Anchor wash down pump

     110 Volt AC system:

• Mason 44 custom 120-volt AC distribution panel
• Shore Power connection for 50-amp service
• Shore power cords and adapters for 30 amp and 50-amp service
• Luco Battery charger
• Galvanic isolator
• Xantrex 3000-watt inverter/charger
• AC 110v outlets, (4) with GFCI protection
• AC 110 water heater
• CruiseAir air conditioning system
• Reverse cycle heat
• Microwave oven

     “The cabin plan incorporated into the Mason 44 was designed with a dedication to function and comfort offshore as well as dockside living. Interior joiner work is of hand-rubbed, satin-finished teak, including a teak ·and spruce cabin pole. Urethane varnish is used throughout and provides a beautiful, long-lasting finish which can be cleaned with soap and water. To offset the darkening effect of the teak, white Formica is used for the yacht's cabin side and overhead. The interior is light and airy. 

     One of the most important aspects of any cruising boat which is to be used in warm climates is ventilation. Nine large opening stainless-steel portside standard. Each cabin, including the head has opening marine windows. Under rough conditions when the ports cannot be opened, air circulation is insured by five dorade vents. These vents provide more than ample air circulation to all parts of the boat under the most adverse conditions and when the boat is left locked up unattended. 

     The standard Mason 44 layout is a development of the proven MASON 43 and upon close inspection of the cabin plan it should be noted that a tremendous amount of usable storage exists. Access doors are provided to every nook and cranny, under bunks, seats, floorboards / companionway stairs, etc., lockers are large and deep, and all finished with an insulating material and painted with an enamel paint. ·There is also substantial storage beneath the cabin sole because of the-full deep underbody of the boat. 

     It should be noted that careful attention has been given to handholds, rounded corners, countertop fiddles, deep sinks etc. Often these items are the last things noticed by a Buyer during an inspection and only after he really begins to sail the boat does he recognize the importance of them. 

     The MASON 44 offers full length "valance type" grab rails on the port and starboard side below the opening stainless-steel ports. These grab rails are easy to reach on both port and starboard tack and also double as water traps should any water dribble in thru an open port. There grab rails drain from their lowest point thru a drain into the bilge.” ~ Pacific Asian Enterprises

     Entering Entropia’s interior from the offset companionway off to port is the large well ventilated aft cabin that features:

• Overhead hatch
• Overhead lighting
• Opening port lights
• Reading lights
• 12-Volt Hella fan
• Bookshelves forward and inboard
• Shelf and locker storage outboard above bunk
• Ships clock and barometer
• Drawer storage inboard and below bunk
• Additional locker storage below bunk

      Exiting the aft cabin and entering the main salon to starboard and outboard is the strategically placed navigation station that is centrally located at the base of the companionway steps and central to the interior. This are also features:

• Hanging locker aft
• Dome lighting under soffits
• Suite of electronics (see Electronics)
• Electrical distribution panels and displays (see Electrical Systems)
• Chart light (red and white)
• Built in magazine/chart rack
• Outboard opening chart table
• Swingout custom upholstered pedestal seat with wrap around back and arm rests
• Drawer and locker storage below tabletop

     Turning to port is the large well protected galley that features plenty of working surfaces and storage while maintaining a safe and usable area at sea. Of note is:

• Overhead lighting
• Opening ports out board
• GoldStar microwave
• Top loading and front-loading refrigerator/freezer box with 110 volt (2019) and engine driven refrigeration (2018)
• Drawer and locker storage inboard
• Locker storage outboard and above work surfaces
• Gimballed Force-10 3 burner propane range with oven and broiler ~ 2019
• Propane solenoid
• 120-Volt outlet with GFI
• Top loading storage below countertop outboard and forward
• Stainless-steel deep double basin sinks
• Pressurized fresh water hot/cold mixer head
• Pressurized spray nozzle with flexible hose
• Manual freshwater pump
• Flip up additional work surface inboard

     Moving forward from the galley you enter the spacious well-lit salon with wrap around dinette and to port and a bench sea to starboard with a blue and green classic striped pattern that accentuates the teak joinery. Also featured:

• Overhead dome lighting
• Overhead deck hatch 
• Opening port lights port and starboard with curtains
• Fixed port lights port and starboard with curtains
• Kerosene light with chimney
• Articulating lighting under soffits port and starboard
• Locker and shelf storage outboard and above seating
• Speakers
• Samsung TV
• Double fold out leaf dining table 
• Built in end table with drawers and locker to starboard forward and outboard
• Locker storage above end table
• Hanging locker starboard and forward outboard

     Entering the companionway between the salon and the head/forward cabin you pass buy built in locker storage outboard and to starboard and opposite this is the access from the salon to the head with separate shower stall. Of note in this area is:

     Shower Stall

• Overhead hatch
• Shower wand with pressurized hot/cold fresh water fresh with flexible hose and mounting bracket
• Locker storage outboard
• Bench seat in stall
• Storage below bench seat
• Teak shower grate with sump below

     Head

• Overhead dome lighting
• Opening port light
• Vanity with mirror
• Locker storage outboard and below sink
• Manual marine head
• Stainless-steel single basin sink
• Pressurized hot/cold freshwater mixer head

     Continuing forward you enter the forward cabin with a traditional v-berth with infill, upholstered with the same blue and green classic striped pattern that is in the salon. Also highlighted in this cabin:

• Overhead deck hatch
• Overhead dome lighting
• Opening port lights port and starboard
• Locker and shelf storage above bunk
• Opening locker door to the chain locker forward
• 12-Volt Hella fan
• Reading lights port and starboard
• Storage below bunks
• Single seat with upholstered cushion below infill 
• Battery switches and windlass breaker
• Hanging locker aft and out board to starboard

• 205-Gallons of water in (5) stainless steel tanks
• (2) Sinks with mixing faucet
• Stall freshwater shower with wand on flexible hose
• Pressure water pump and accumulator tank
• Fresh water deck fill
• 11-Gallons hot water heater

     A Certified Professional Yacht Broker (CPYB) is recognized as having achieved the highest level of industry accreditation, available only to fully-qualified yacht sales professionals. The CPYB program is administered by Yacht Brokers Association of America in partnership with Florida Yacht Brokers Association, Northwest Yacht Brokers Association, California Yacht Brokers Association, Boating Ontario Dealers, British Columbia Yacht Brokers Association and Gulf Coast Yacht Brokers Association.

     The CPYB program is also endorsed by the Marine Retailers Association of the Americas (MRAA) Marine Industry Certified Dealership (MICD) program and leading yacht manufacturers as a key component of their own industry standards; the highest level of achievement for their member yacht sales professionals.

Experience & Validity

     The CPYB designation is earned by eligible yacht sales professionals, who, after serving a minimum of three years as a full-time professional, have successfully completed a comprehensive written examination to validate professional competency.

Continuing Education

     A CPYB is committed to their personal and professional development through continuing education, as mandated for CPYB recertification every three years.

Ethics & Standards

     A CPYB adheres to, and is accountable to, a nationally recognized Code of Business Ethics and conducts yacht sales transactions in accordance with a stringent set of industry standards of practice.

Fiduciary Responsibility

     A CPYB maintains a dedicated escrow/trust account to protect their client’s funds. A CPYB understands their fiduciary responsibility and obligations with respect to client funds.

Transaction Management

     A CPYB uses proven, industry-recognized transaction documents, which fully and clearly describe all terms and conditions of a transaction. Honesty & Integrity A CPYB maintains the highest standards of professionalism, acting with honesty and integrity.

Trust & Confidence

     A CPYB instills confidence, trust and consistency in all transactions involving fellow yacht sales professionals for the benefit of the client.

     The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.